• ISO 9001:2015, IS0 45001:2018 Certified company

Brochure

ASTM A335 P11 Alloy Steel Seamless Pipe

Alloy Steel A335 P11 Seamless Pipe Distributor, ASME SA 335 Alloy Steel P11 Pipe, Stockist of UNS K11597 Alloy Steel Pipe

ASTM A335 Grade P11 is also commonly known as ASME SA335 Grade P11 Pipes, it is a seamless ferritic alloy-steel pipe that mainly has high-temperature applications. The UNS designation for this grade P11 is K11597.

The key elements of P11 pipes are carbon, manganese, phosphorous, sulfur, silicon, chromium and molybdenum. Its key components are chrome and moly that provide it with strength, resistance against wear, hardenability as well as corrosion resistance properties. It is also possible to heat treat this alloy. The chromium within the alloy increases its resistance to oxidation allowing it to be used in corrosive high-temperature environments. Molybdenum addition enhances strength and wear resistance.

ASTM A335 Grade P11 Seamless Pipe

ASTM A335 Grade P11 Seamless Pipe

ASTM A335 P11 Pipe

ASTM A335 P11 Pipe

P11 Alloy Steel Seamless Pipe

P11 Alloy Steel Seamless Pipe


These pipes are highly important for transformers and electric motors as this equipment use the magnetic properties of the P11 Alloy for certain tasks. Seamless pipes of this alloy have less roughness which is important for certain sensitive applications. The ASTM A335 P11 pipes are majorly used in the oil and gas, petrochemical, and power generation industries.

Table of Contents

We at N-Pipe Solutions Inc. stock a wide range of ASTM A335 Gr. P11 pipes

  • Pipes are offered from size ¼” NPS up to 24” NPS, however large-diameter pipes above 24” NPS can also be provided upon clients request.
  • Pipes thickness range from SCH 20 up to SCH XXS as per ANSI B36.10 / ASME B36.10
  • We can also offer non-standard thickness which is not available in the above dimension standard.
  • These pipes can be supplied in a single random length of 4 – 7 Meters long and double random length of 7 – 12 Meters long, if there is a client’s requirement, we can also provide fixed length pipes.
  • Pipes can be offered with Mill test certificate as per EN 10204 3.1 and 3.2
  • Pipes can be all offered with IBR Form III meeting the Indian boiler requirements.
  • Pipes can be supplied with additional specifications NACE MR0175, NACE MR0103, H2 Service, Wet H2S Service, AXN1, AXN2, AXN3, AXN4, UOP1, UOP2, NAC4, NAC6, NAC7.
  • Pipes can be offered under any Third-party inspection agency of client choice.
  • Alloy Steel ASTM A335 available grades A335 P1 Alloy Steel Pipe, ASTM A335 P5 Alloy Steel Pipe, ASTM A335 P9 Pipe, A335 P22 Alloy Steel Pipe, A335 P91 Alloy Steel Pipe.

N-Pipe Solutions Inc. is a major supplier of Low Alloy steel Seamless pipes from India. We provide high-quality pipes to clients throughout the world. Pipes are stock in NPS/NB dimension as per ASME B36.10 in various thicknesses as per clients requirements. All pipes supplied by us are duly inspected by our in-house quality control department before being supplied to the client. All pipes are available with complete traceability and mill test certificate as per EN 10204 3.1.

We provide the best competitive prices to our clients backed by quality service.


Scope of ASTM A335 GR. P11

This specification covers nominal wall and minimum wall seamless ferritic alloy-steel pipe intended for high-temperature service. Pipe ordered to this specification shall be suitable for bending, flanging (vanstoning), and similar forming operations, and for fusion welding. Selection will depend upon design, service conditions, mechanical properties, and high-temperature characteristics.


Referenced Documents

2.1 ASTM Standards:

A999/A999M Specification for General Requirements for Alloy and Stainless Steel Pipe

E92 Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials

E213 Practice for Ultrasonic Testing of Metal Pipe and Tubing

E309 Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation

E381 Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings

E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

E570 Practice for Flux Leakage Examination of Ferromagnetic Steel Tubular Products

2.2 ASME Standard:

B36.10M Welded and Seamless Wrought Steel Pipe


Ordering Information

    Orders for material under this specification should include the following, as required, to describe the desired material adequately:

  • Quantity (feet, metres, or number of lengths),
  • Name of material (seamless alloy steel pipe),
  • Grade (Table 1),
  • Manufacture (hot-finished or cold-drawn),
  • Size using one of the following:
      • NPS and schedule number,
      • Outside diameter and nominal wall thickness,
      • Outside diameter and minimum wall thickness,
      • Inside diameter and nominal wall thickness, and
      • Inside diameter and minimum wall thickness.
  • Length (specific or random),
  • End finish (Ends Section of Specification A999/A999M)


General Requirements

Material furnished to this specification shall conform to the applicable requirements of the current edition of Specification A999/A999M, unless otherwise provided herein


Heat Treatment:

All pipes shall be reheated for heat treatment and heat-treated by the requirements of Table 2.

TABLE 2 Heat Treatment Requirements A

Grade Heat Treat Type Normalizing Temperature, min or range °F [°C] Cooling Media Subcritical Annealing or Tempering Temperature, min or range °F [°C]
P1 full or isothermal anneal or -- -- --
normalize and temper or -- -- 1200 [675]

A Where ellipses (--) appear in this table there is no requirement.


Chemical Composition of ASTM A335 Gr. P11 Pipes

Grade UNS Designation A Carbon Manganese Phosphorus, max Sulfur, max Silicon Chromium Molybdenum Others
P1 K11597 0.05-0.15 0.30–0.60 0.025 0.025 0.50-1.00 1.00-1.50 0.44–0.65 --

A New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
D Applies to both heat and product analyses.


Mechanical properties of ASTM A335 Gr. P11 Pipes

Grade Tensile strength, min: Yield strength, min: Elongation Requirements
KSI MPa KSI MPa Longitudinal Transverse
P1 60 415 30 205 30 20

Permissible Variations in Diameter

1) For pipe ordered to NPS [DN] or outside diameter, variations in outside diameter shall not exceed those specified in Table 6.
2) For pipe ordered to inside diameter, the inside diameter shall not vary more than +/- 1 % from the specified inside diameter.

NPC [DN] Designator Over Under
in. mm in. mm
1/2 to 1 1/2 [6 to 40],incl. 1/64 (0.015) 0.40 1/64 (0.015) 0.40
Over 1/2 to 4 [40 to 100],incl. 1/32 (0.031) 0.79 1/32 (0.031) 0.79
Over 4 to 8 [100 to 200],incl. 1/16 (0.031) 0.79 1/16 (0.031) 0.79
Over 8 to 12 [200 to 300],incl. 3/32 (0.031) 0.79 1/32 (0.031) 0.79
Over 12 [300] ± 1% of specified outside diameter

Permissible Variations in Wall Thickness

In addition to the implicit limitation of wall thickness for pipe imposed by the limitation on weight in Specification A999/A999M, the wall thickness for pipe at any point shall be within the tolerances specified in Table 7. The minimum wall thickness and outside diameter for inspection for compliance with this requirement for pipe ordered by NPS [DN] and schedule number is shown in ASME B36.10M.

NPS [DN] Designator Tolerance, % form Specified
Over Under
1/8 to 2 1/2 [6 to 65] incl., all t/D ratios A 20.0 12.5
Above 2 1/2[65], t/D<=5%A 22.5 12.5
Above 2 1/2[65], t/D>5%A 15.0 12.5

A t= Specified Wall Thikness; D=Specified Outer Diameter.


Hydrostatic test

The pipes need to be Hydro tested as per ASTM A530.


Mechanical Tests Required

Transverse or Longitudinal Tension Test, Hardness Test, and Flattening or Bend Test

  • For material heat treated in a batch-type furnace, tests shall be made on 5 % of the pipe from each treated lot. For small lots, at least 1 pipe shall be tested.
  • For material heat treated by the continuous process, tests shall be made on a sufficient number of pipe to constitute 5 % of the lot, but in no case less than 2 pipe.
  • Unless otherwise specified, the flattening test or bend test shall be chosen at the manufacturer’s option.


Certification

Certification and test reports, as described in Section 25 of Specification A999/A999M, are required.


Marking on pipes

16.1 In addition to the marking prescribed in Specification A999/A999M, the marking shall include the length, the schedule number, if the pipe is ordered to a schedule number, and the heat number or manufacturer’s number by which the heat can be identified. An additional symbol “S”, if the pipe conforms to any of the Supplementary Requirements S1 to S6, The marking may be by stenciling, stamping, or rolling at manufacture’s option.
Furthermore, the marking designated in below table to indicate the test method(s) shall be included.

Marking to indicate the test method(s)
Hydrostatic Non Destructive Marking
YES NO Test Pressure
NO YES NDE
NO NO NH
YES YES Test Pressure/NDE

NDE can be any of the following: Ultrasonic / Flux Leakage / Eddy Current


Biggest stockiest of Pipes with Mill Test Certificate as per EN 10204 3.2 Certification

Contact Us